Air Bending vs Bottoming vs Coining on a Press Brake

Start with air bending for most V-bends. The punch sets the angle mainly by how far it enters the die, so one suitable tool set can form several angles. Bottoming seats the sheet more closely against matched tools. Coining applies much higher local pressure to set the bend. Those differences affect force, inside radius and the amount of springback after unloading.

Before choosing a method, check the drawing for the finished angle, inside radius and shortest flange. Then verify that the tooling fits the part and that the machine and tools can carry the required load. An angle that looks right on a test piece does not prove the setup is within its ratings.

How the Three Methods Contact the Sheet

Air Bending

Air bending is a very common forming method used on CNC press brakes. As the punch moves downward, the sheet metal is bent between the shoulders of the bottom die and the tip of the punch. The sheet is supported or contacted primarily at three points and does not come into full contact with the bottom of the V-groove.

Punch penetration primarily controls the angle under load. A single V-die can cover several angles within the limits of the punch profile, die angle and part clearance.

Air bending usually needs less force and makes changeovers easier. The unloaded part springs back, so use a measured trial bend or a validated angle-measurement system to set compensation for the actual material and tooling.

Bottoming

In bottoming, matched punch and die geometry brings the sheet into closer contact with the tool faces. The tool profile has more influence on the loaded shape than it does in air bending.

Bottoming generally needs more force than air bending. Match the tooling to the material, thickness and target angle, and measure the part after unloading. Some springback can remain.

In this guide, bottoming means seating the sheet more closely against the tools. Coining is treated separately because it deliberately compresses the bend zone under much higher local pressure.

Coining

In coining, the punch applies high local pressure that plastically compresses the material around the bend. This makes the part conform more closely to the tool profile and can leave local thinning. Check the resulting geometry and part requirements before choosing the process.

Coining can reduce springback substantially, but it places greater demands on the punch, die, holders and press brake. The force depends on the particular tool and part, not a fixed multiple of the air-bending load.

Use coining only when the part needs it and the machine and tooling suppliers confirm the process and load limits.

Comparison of Force Angle and Tooling

CheckAir bendingBottomingCoining
Tool contactPunch nose and two die shouldersSheet seats more closely against matched toolsHigh local compression at the bend
ForceUsually lowest of the threeGenerally higher than air bendingTypically highest; verify for the job
Angle controlMainly punch penetrationMore dependent on matched tool anglesTool profile and local plastic compression
SpringbackAllow for elastic recoveryCan be reduced; measure after unloadingOften much lower, not guaranteed zero
Inside radiusV opening, material and tool geometryMore dependent on tool profileClosely tied to the forming tool
ToolingOne suitable set can cover several anglesMatched punch and dieRated tools for high local load
First use to testGeneral bending and frequent changeoversJobs that benefit from seating to matched toolsParts that need the specific coining effect

The table gives relative trends, not force ratings. For bottoming or coining, obtain force data for the actual material, bend length and tooling. Confirm the machine’s local and off-center load limits as well as total rated force.

Why Shops Start with Air Bending

The flexibility of air bending matters in a shop that changes material or part design often. A suitable punch and V-die can handle several jobs without replacing a matched tool set for every angle.

V opening is a trade-off. For the same material, thickness and bend length, a smaller opening generally raises the air-bending force and can help achieve a smaller inside radius. A larger opening generally lowers force but can require a longer flange for support.

On a CNC press brake, use a test part to verify the angle, backgauge position and sequence before releasing the program. Angle measurement can help compensate for variation where fitted; it does not replace first-part checks.

Ram depth changes the angle. It does not let the operator choose any inside radius. Verify the radius with the actual V opening, material and punch geometry.

Estimating Force for Each Method

Check force before attempting a trial bend. Compare the expected load with both machine and tooling ratings for the loaded length and position.

Air Bending Force Example

The BEIGEMA press brake tonnage calculator estimates conventional air-bending force from tensile strength, thickness, active bend length and V-die opening. Its optional planning allowance is separate from the base force.

At a reference tensile strength of 450 MPa, the calculator’s simplified air-bending expression is:

F (kN) ≈ 650 × t² × L ÷ V

  • F = estimated bending force in kilonewtons (kN).
  • t = sheet thickness in millimeters (mm).
  • L = active bend length in meters (m).
  • V = V-die opening in millimeters (mm).

Use this coefficient only for the stated reference material and conventional air bending. Enter the actual tensile strength in the calculator when it is known. For metric tonne-force, divide kN by approximately 9.81.

Example: 3 mm mild steel at the 450 MPa reference, a 2 m active bend and a 24 mm V opening.

F ≈ 650 × 3² × 2 ÷ 24 = 487.5 kN

That is about 49.7 metric tonne-force in total, or 243.8 kN per meter of active bend.

This result is not a 50-ton machine recommendation. Check the rated load per length for the punch, die and holders, the machine’s off-center and short-bend limits, and the actual material before selecting equipment.

Bottoming Force

More contact between sheet and tools generally raises the load. Ask the tooling supplier for bottoming data for the actual profile. Do not size this setup using the air-bending result or a generic multiplier.

Machine capacity and tooling capacity are separate limits. Even if the press brake can deliver the total force, the punch, die or holder may be overloaded over the active length.

Coining Force and Local Loading

Coining concentrates force at the bend zone. The contact area, tool profile and material behavior determine the load, so a conventional air-bending calculator cannot validate a coining setup.

Obtain process-specific load data and written limits for the press brake, tooling and clamping system. Verify the load path and active length before trying the job.

If the concern is angle repeatability, first check material variation, tool seating, radius and validated angle compensation. Consider coining only if those measures cannot meet a requirement the part actually has.

Springback and the Finished Angle

Springback is the elastic change in angle or shape after the load is removed. Material condition, thickness, inside radius and the method all affect it. Use the drawing’s angle convention when comparing an unloaded part with a programmed angle.

An air-bent part may need to be formed to a slightly smaller included angle under load to reach the target after unloading. Determine the correction on the actual material; do not assume a fixed number of degrees.

Bottoming can reduce springback by seating the sheet more closely against the tools. Tool geometry, wear and material variation still affect the unloaded angle, so check it on a trial part.

Coining can reduce springback further. It still does not guarantee a perfect angle: tool wear, material and load distribution can change the result.

Verify force and clearances first. Make a controlled trial bend, measure the unloaded angle and radius, adjust within the approved setup, and confirm repeatability before running a batch.

Matching the Inside Radius to the Tooling

The drawing radius guides the tool choice. For conventional air bending, consider the V opening, grade, thickness and punch nose before estimating the achieved radius.

A wider V opening tends to produce a larger inside radius in ordinary air bending. A tighter opening usually increases force and can raise the risk of marking or cracking. Check the supplier’s forming data and a trial part, especially when the bend crosses a critical rolling direction or the drawing limits cracking.

Bottoming and coining depend more on the tool profile. Confirm punch and die geometry together, including flange support, clearance and possible collision with previously formed features. Review special press brake tooling when the standard punch cannot clear a formed flange.

When the radius tolerance is tight, verify three things: the material’s formability at the target radius, the proposed tooling’s geometry and the allowable load over the active bend length.

If a standard setup cannot meet the geometry, assess special tooling or a different forming method. Increasing force is not a substitute for that check.

Choosing a Bending Method

Choose air bending when a validated setup meets the drawing with a suitable radius, angle and finish. Its lower force and flexible tool setup make it a useful starting point for most jobs.

Evaluate bottoming when the job benefits from a matched tool profile and a trial confirms it meets the drawing. Recheck machine and tooling ratings before changing methods.

Evaluate coining only for a part that needs its local forming effect. Confirm the method, tool and permissible loads with the suppliers before any trial.

What to Send for a Setup Review

Send the part drawing, material grade and tensile strength, thickness, active bend length, flange dimensions, target inside radius and tolerance. Identify the proposed tooling and bending method, and include the machine model if you are checking an existing press brake. Include the punch and die profiles when discussing press brake tooling options.

For an air-bending job, attach the press brake tonnage calculator result to your request. For bottoming or coining, ask for process-specific force and tooling data instead.

Related pages

Related guides

Machines by category

Contact Us

For Immediate Assistance, Please Contact us Now!