A press brake setup that works well for mild steel may not produce the same results when you switch to aluminum or stainless steel. The bending force changes, the final bend angle may differ because of springback, and the same punch and V-die combination may not be suitable for every material. Also consider the guide to What Is a Hydraulic Press Used For? 12 Shop-Floor Jobs.
For shop owners and operators taking on aluminum or stainless steel jobs for the first time, the challenge is not simply choosing the right bending force. It is knowing which machine settings, tooling choices, and handling procedures need to change before production begins.
This guide compares aluminum, stainless steel, and mild carbon steel from a practical press brake perspective. It explains how to check springback, select an appropriate V-die opening, reduce aluminum cracking, and protect stainless steel surfaces—so you can make a controlled material changeover instead of relying on repeated trial and error.

What Changes When You Switch from Carbon Steel?
If your press brake is already set up for mild steel, switching to aluminum or stainless steel may require more than a simple program change. Even when two sheets have the same thickness, they can behave differently during bending because of differences in yield strength, ductility, work hardening, and elastic recovery.
These differences affect the bending force, the final bend angle, the inside radius, and the risk of surface damage or cracking. Using the same punch, V-die opening, and CNC settings without checking the material can lead to inconsistent angles, damaged parts, or unnecessary tool loads.
Before starting a new job, focus on five areas: bending force, springback, minimum inside bend radius, tooling selection, and surface protection.
Springback in Sheet Metal: Aluminum vs. Stainless Steel
Springback in sheet metal occurs when the material partially returns toward its original shape after the bending force is removed. For example, a sheet bent to 90° under load may open to 93° after unloading.
When switching from mild steel to aluminum or stainless steel, the same press brake settings may produce different results. Springback depends on yield strength, elastic modulus, material grade, thickness, inside bend radius, and bending method. Stainless steel can exhibit significant springback, while aluminum's behavior varies considerably with alloy and temper.
Why Do These Materials Behave Differently?
Yield strength: Higher yield strength can contribute to greater springback under comparable bending conditions.
Elastic modulus: Aluminum has a lower elastic modulus than steel, so its elastic recovery must be evaluated alongside its strength.
Work hardening: Stainless steel, particularly grade 304, can strengthen during deformation, affecting its bending behavior.
Therefore, do not apply a fixed springback value to every aluminum or stainless steel job.
How to Determine Springback Compensation
The most reliable method is to make a test bend using the actual material and tooling.
- Confirm the material grade, temper, and sheet thickness.
- Select a suitable punch and V-die opening.
- Make a test bend and measure the angle after unloading.
- Compare the measured angle with the target angle.
- Adjust the CNC settings and repeat the test until the required angle is achieved.
If a target 90° bend opens to 93° after unloading, the measured error is 3°. Correct the angle or depth using the controller’s convention, then make another test bend. A 3° error does not guarantee that changing the programmed angle by exactly 3° will give the final result.
How to Adjust CNC Press Brake Settings
On a CNC press brake, springback compensation generally involves adjusting the commanded bend angle or ram position.
Angle programming: Correct the angle command according to the controller's programming convention.
Depth programming: Make a controlled ram-position adjustment and check the resulting angle.
Automatic angle compensation: Verify sensor calibration and follow the manufacturer's instructions.
The required correction depends on the controller, tooling, and material response.
Practical tip: Record the successful settings for each material and thickness. When changing from mild steel to aluminum or stainless steel, always verify the first part before starting full production.
Use the press brake tonnage calculator for a preliminary force estimate, then check the actual material data and tool ratings.
Minimum Bend Radius: How Much Radius Does Each Material Need?
The minimum inside bend radius is the smallest radius a sheet can typically withstand without unacceptable cracking or damage during bending. Choosing a radius that is too small can cause cracks on the outside of the bend, particularly when working with less ductile materials.
The required radius depends on material grade, temper, thickness, bending direction, and tooling. Aluminum alloys can vary significantly in formability, while stainless steel often requires attention to work hardening and springback.
Material Differences That Affect the Bend Radius
Minimum inside radius must be checked for the exact alloy, temper, thickness, rolling direction and forming method. The table identifies the relevant checks rather than prescribing one radius ratio for every sheet.
| Material | Radius selection check |
|---|---|
| Mild carbon steel | Use the specified grade, thickness and tool data; confirm the actual air-bent radius. |
| 5052-H32 aluminum | Often more formable than 6061-T6; still check thickness, rolling direction and the supplier’s minimum radius. |
| 6061-T6 aluminum | Tight bends can crack; obtain grade- and thickness-specific data or assess a more formable condition. |
| 304 stainless steel | Check condition, work hardening, radius and springback; do not use one universal radius-to-thickness ratio. |
For example, a tight radius that is feasible in one 5052-H32 sheet may crack a 6061-T6 sheet of the same thickness. Obtain grade- and thickness-specific bending data before selecting the tooling.
Use the supplier’s data as a starting point and verify the achieved radius and surface condition on a trial bend with the actual sheet and tools.
How to Choose the Right Bend Radius
Before selecting a punch and V-die, check three things:
Material grade and condition: Do not assume all aluminum alloys have the same ductility.
Sheet thickness and rolling direction: distinguish a bend line parallel to the rolling direction from one perpendicular to it. Check the supplier’s preferred orientation, particularly for less ductile aluminum alloys.
Tooling geometry: The punch nose radius and V-die opening influence the resulting inside radius during air bending.
If cracks appear along the outside of the bend, do not simply increase the bending force. Check the material condition, rolling direction, and whether a larger inside radius is required.
Practical tip: If a drawing specifies a tight bend radius, confirm that the material and tooling can achieve it before production. A slightly larger radius may prevent cracking, reduce scrap, and improve consistency.
Aluminum Cracking: Check the Alloy and Rolling Direction
When bending aluminum sheet metal, cracks often appear along the outside of the bend, where the material experiences tensile stress. Before changing the press brake settings, check the alloy, temper, rolling direction, and inside bend radius.
Check the Rolling Direction
The bend line is often arranged perpendicular to the rolling direction when aluminum cracking is a concern. Confirm the orientation against the material producer’s guidance; do not rely on the ambiguous phrase “bend across the grain” without defining the bend line.
If cracks repeatedly appear along the bend line, check the sheet's grain direction and compare the part orientation with the material supplier's recommendations.
Check the Alloy and Temper
Not all aluminum grades have the same formability.
5052-H32: Commonly used for sheet-metal parts and generally offers good bendability.
6061-T6: Higher strength but more prone to cracking during tight bends.
Annealed aluminum: Generally more ductile and easier to form than the same alloy in a harder temper.
If a part cracks despite using suitable tooling, verify the material grade and temper before adjusting the machine.
Check the Inside Radius and Cut Edges
A radius that is too small increases tensile strain on the outside of the bend. Sharp burrs, notches, and rough laser-cut or sheared edges can also act as crack initiation points.
Before production, confirm that the punch radius is suitable for the material and thickness. Inspect cut edges and remove problematic burrs where necessary.
What to Check When Aluminum Cracks
Follow this troubleshooting sequence before increasing bending force:
- Material: Confirm the alloy and temper against the purchase specification.
- Rolling direction: Check whether the bend line runs parallel to the rolling direction.
- Bend radius: Determine whether the inside radius is too small for the material.
- Cut edges: Inspect for burrs, notches, and edge damage.
- Tooling: Verify punch radius, V-die opening, and alignment.
Increasing tonnage alone will not solve a material ductility problem and may increase the risk of tool overload or part damage.
Practical tip: If aluminum cracks during the first test bend, stop and identify the cause before continuing production. A more suitable material temper, larger inside radius, or corrected blank orientation may be more effective than changing the press brake force.
V Die Opening and Tooling Adjustments
When switching from mild steel to aluminum or stainless steel, the existing press brake tooling may not be suitable for the new material. The V-die opening and punch radius affect the inside bend radius, bending force, surface quality, and risk of cracking.
When to Change the V Opening
For air bending mild steel, a V-die opening of approximately 6–8 times the sheet thickness is often used as an initial guideline. However, this ratio is not suitable for every material or application.
Aluminum: Choose an opening that provides sufficient bend radius and reduces cracking risk, especially for less ductile alloys such as 6061-T6.
Stainless steel: Check the required bending force, springback, inside radius, and allowable tooling load before selecting the opening.
Thin or narrow-flange parts: Confirm that the selected die opening is compatible with the minimum flange length and part geometry.
A larger V-opening generally produces a larger inside radius in air bending and can reduce the required bending force, but it may not suit every drawing or flange dimension.
Choosing the Punch Radius
The punch nose radius influences the resulting inside radius and the strain experienced by the material.
Aluminum: Avoid an excessively small punch radius that may cause cracking.
Stainless steel: Select a radius that meets the drawing requirements while accounting for springback and surface finish.
All materials: Check the actual punch geometry and test the resulting bend radius rather than assuming it will exactly match the punch nose radius.
Checking Compatibility and Load Limits
Before installing a different punch or die, confirm:
- The punch and die fit the machine's clamping system.
- The installed tool heights, machine open height and available stroke allow loading, bending and removal without interference.
- The tooling's rated load is sufficient for the application.
- The selected V-opening and punch radius meet the part drawing requirements.
- The tooling surfaces are clean and suitable for the required finish.
Physical fit does not always mean functional compatibility.
Practical tip: When changing materials, verify the V-die opening and punch radius before adjusting CNC settings. Correct tooling selection helps reduce cracking, surface damage, excessive springback, and unnecessary machine loads.
For stainless steel, prevent embedded carbon-steel contamination by using clean contact surfaces and suitable handling methods. Where cosmetic finish is important, evaluate protective film or non-marking tooling and verify the first part.
Compare the available press brake tooling options against your material and drawing.
Material Changeover Checklist
When switching from mild steel to aluminum or stainless steel, do not assume that the existing press brake program will produce the same results. Check the material, tooling, bend angle, and surface requirements before starting production.
| Checkpoint | Aluminum | Stainless steel | Action |
|---|---|---|---|
| Material grade | Confirm alloy and temper | Confirm grade, such as 304 or 316 | Verify material specifications |
| Sheet thickness | Measure actual thickness | Measure actual thickness | Recheck the bending program |
| Bending force | Recalculate if necessary | Recalculate; force may be higher | Stay within machine and tooling limits |
| Springback | Verify by test bending | Pay attention to springback and work hardening | Adjust CNC settings based on measured results |
| V-die opening | Check radius and cracking risk | Check force and target radius | Select suitable tooling |
| Punch radius | Avoid radii that may cause cracking | Match the drawing and forming requirements | Confirm the resulting inside radius |
| Surface protection | Prevent dents and marks | Use non-marking tooling or protective pads when needed | Inspect contact surfaces |
| First-piece inspection | Check cracks and bend angle | Check angle, scratches, and die marks | Approve the first part before batch production |
Before You Start Production
Use this quick checklist for every material changeover:
- Confirm the material grade, temper, and thickness.
- Verify the punch radius and V-die opening.
- Check the CNC program and machine load limits.
- Make a test bend and measure the unloaded angle.
- Inspect the inside and outside of the bend for cracks or surface damage.
- Record the verified settings for repeat production.
The key is to adjust the setup based on the actual material and part requirements, rather than applying a fixed correction to every job.
If you are selecting a press brake for different materials or thicknesses, BEIGEMA can evaluate the bending force, tooling configuration and machine specifications against your drawings and production requirements. Use BEIGEMA press brake range as a starting point for aluminum and stainless-steel bending setups; send your material grade and bend drawing for review (Press Brake Machine).
Related pages
Related guides
- Hemming, Gooseneck and Special Press Brake Tooling
- Press Brake Operation from Setup to First Part Inspection
- Sheet Metal Fabrication for Electrical Enclosures
- Air Bending vs Bottoming vs Coining on a Press Brake
- Laser Cutting vs Waterjet for Metal Parts
- Press Brake Safety and Safeguarding
- How a Fiber Laser Cutting Machine Cuts Metal
- How to Choose a Press Brake: A 7-Step Buyer’s Guide
